So Behind!

For the corset sew-along, that is.  I got to distracted trying to finish my other corset...and then dogs and going back to school got in the way, and I haven't felt like sewing!  I'm pinning the final pieces together currently, we'll see how long that all takes. 

But I am finished with my underbust corset!  I took some better pictures this time:

I'm quite pleased with the binding at the top front, although the bottom is just a tad uneven.  I used a blanket binding  method, by the way.  I cut out two-inch wide strips of my fashion fabric, folded it in half, sewed it to the top edge of my corset with the raw edges  next to each other (like I was sewing a side seam), and then turned the folded edge over and stitched it down from the front.  Since it was a knit suedecloth, it molded itself around the edges perfectly.  It doesn't look the best in the inside, but that's because my strips were a little too thin, I think--if they were wider, it would have allowed my stitches to catch the binding on front and back.  It's secure, though, so I'm not worrying.   

The side view is the same one I showed last time; I fixed the wrinkle almost completely!  The loose thread is still there in the photo, though--I still need to tie it down and hide the ends.

The back is still not a great photo, but it will do.  I vertically boned my modesty panel with three leftover bones, but I should have done some horizontal boning, because as you can see, it wrinkles together.    I made a "floating" panel, so it's being held to the corset by two sets of grommets which the lacing goes through, but I'm thinking if I tack down the one side of it to make it an adhered panel, it may be easier to coax into laying flat when I put it on.

And for a bit of a better view of the shape it gives, here's a slightly farther away shot... the lighting turned out bad, but you can still see the silhouette.

Yes, those are my xbox huge hips that flare out even to the hem of my shirt and after.  I'm wearing the corset loosely, so it only compresses my waist by about 1.5 or 2 inches, but the effect looks good so far.

For Your Aching Bones..

A heating pad!

I made this a while ago, but since I had a chance to use it recently, I figured why not take some pictures before it gets even MORE covered in fuzz.

It's really just a basic rice-filled cotton bag.  That's all.  There are so many tutorials for them out there on forums and blogs, but to me they're either too floppy (just a sack the rice can fall all around in--thanks, gravity) or too structured (sewing the rice into tiny little tubes works fine, I suppose, but when you stuff it too much it won't really conform to all your achy curves).

So, I combined the two ideas and sewed mine together with four separate stitch lines, neither of which intersect or connect.  You can kind of see the stitchings in the picture--they stop in the center before the middle skull in the trio's teeth, and they stop before the edges of the bag, as well.  The little unsewn sections provide some place for the rice to move around to, but it will mostly evenly stay in the four sections.  This means you can wrap the bag around your neck, drape it over your shoulder blades, lay on it...whatever you like. The rice won't all fall to one corner, and the heating pad won't fold like a piece of cardboard! 

I plan to make more, so I can probably shoot a photo of my "pattern" later on.   In the mean time, here's a photo of it holding its shape even after I fold it up--the color is also a little more accurate in this one:

PS: That fabric?  It's some print I found in the remnants at a fabric store around here... I think it's by Robert Kaufman.  But I love it because it's not the normal bright tacky sugar skull print, AND IT REMINDS ME OF HELLBOY.  The moment I saw the print I was reminded of Mike Mignola's simplified skulls and limited color palettes.

But shhh, don't tell anyone I'm a geek.

PSS: Those same "tutorials" on the internet all suggest filling your bags with calming lavender essential oils or some such thing.  Being that I like heating pads to make me feel better so I can, you know, do stuff, and not sleep, I decided to scent mine with a vanilla pomegranate... Bad idea.  Apparently when you heat some essential oils they just smell like cheap plastic laced with fragrance.  So, in the future, I will not be scenting these things, thank you very much.

I Finished It!

Well, almost.  You can see in this rather blurry side picture below that I have ONE major wrinkle still left in my underbust:

So after putting in 10 bones--one  1/2inch one at each seam, and one 1/4th inch one on each side of the grommets--I realized that my corset still retained a lot of the minor wrinkles you can see in my last post.  So I went back and added more bones, this time all 1/4th inch ones. On each side I added two at the front, one at the middle, and one at the back.  This eliminated the problem almost entirely, and it was good enough for me.  So that's 18 bones altogether, not including the busk. I could have put another pair on the opposite side of the grommets, but, well... my hasty sewing errors didn't allow for enough room there.

Then, when sewing the binding on,  I unknowingly moved the top knit layer a teensy bit.  Now my wrinkle is back!  But I'm hoping a few well placed hand stitches along the binding layer will fix it.  I guess this is what I get for securing my knit fashion layer to the duck cloth at the side seams only, and not at the top and bottom, too.

Otherwise, I'm pretty pleased:

I mean, the binding edges aren't perfect, but it was my first time.  I think I may need to make a quickly boned modesty panel because, well, can you SEE that back fat by my laces in that blurry picture?  Overall the corset is a little too small in the top back area, so I get a little "back fat" spillage over the top.  Drafting error #1.  I'm hoping that evens out with a different bra and a little more wearing in, though.  As you can see in the above picture, the bra/shirt combination is also covering the top of my corset, and maybe pushing it down a tiny bit.  I didn't notice this problem with another bra I was wearing during the mockup, and I didn't notice as much of a "back fat" problem, either, so I'm hoping switching back to a different undergarment will fix a bit of the problem.

I ended up taking 1 inch off the length over my hips; the pattern I made cupped them fine, but looked a little dramatic/costume-y. This was drafting error #2: I built the corset to be 9 inches high, but I drafted it as if the 9 inch line went straight from my underbust down to my full hip.  When I edited in the curve I wanted, the line came out to be quite a bit longer than 9 inches, more like 10.5 or so.  (If I were more awake I might have some more technical math and geometry oriented explanations for this, but I just can't find the right words.) I also loosely lengthened the front to accommodate the 9 inch busk I had.  It makes a pretty nice point, I think.

Oh, yeah, and I got size 00 grommets--which work pretty well with my cheap-o grommet setter, and I'll have to post photos later--but I accidentally put in two of them backwards.  I put in a third backwards on purpose after I realized the first one was backwards, to try and "even it out" on each side, but uhh..... yeah, I'm just thoughtless sometimes!  I used the hole punch on this, too, since I could not get 4 layers of duck cloth and two layers of suede cloth to stretch evenly enough to properly put into a grommet.  That's my fault, since I wasn't sure how many layers to keep in the back, and just went for "more is better". 

But I don't even have pictures of the back of my corset at the moment, so that's the third minor finishing touch I still need to do. :)

More of that corset...

I've been really into finishing this the last few days.  Even though I worked, I did some stitching around the edges  of the fashion layer/second strength layer pieces to secure the fabrics together and make them act "as one".  Then I sewed them together the other night....

It's looking pretty good, in my opinion!  There are a few of the hip pieces that "wrinkle" weirdly due to the very curvy seams, but those wrinkles aren't sewn in, so I'm hoping the boning sorts that out.  In fact, I just noticed now that in this picture, the wrinkles are pretty much identical on each side, which leads me to believe my problem may really be as superficial as I think.  The next step is to add boning and really test it out.

Now, here's some shots of the inside to show my method!  You see, I have a habit of trying something different every time I try to construct a corset....even though, like I mentioned before, I've never yet entirely finished one.  For this one, since I was using duck cloth for strength, and was unsure at the time about its properties,  I decided to do an inside layer of duck, and an outside layer of duck topped with my fashion fabric.  They are sewn separately, only connected at the busk so far. 

In this photo, if you enlarge it, you can see that in the fuschia circle there are three sewing lines.  This is my top layer, and the right-most line is the one that is holding my suedecloth to my duck.  The middle line is the base seam holding different panels together, and the left-most line is the topstitching holding the seam--and the seam allowance--down.   In the blue circle, you can see only two lines--the left being the seam, and the right being the top stitching over it.

Now, it might not look like much in the picture, but you'll notice that the seams of both sides are facing the same direction.  That's because the front side is turned over; when properly laid flat, one side of the seams will face left, and one will face right. The plan is to stitch about 1/4th of an inch from a panel's seam on either side, which will leave me with a built in boning casing--the boning will fit between the seam allowances, giving it two to three layers of protection on either side.  I'm not even sure if that will make sense to ME later on, but there you go.

Lastly, because I sometimes fail at sewing overall... there's the one thing bothering me about my construction so far:

Once again, you might have to enlarge it to see it, but this is where my top-stitching kind of wavered--mostly, when I was trying to pull the seam into the right shape at the sharp waist curves, the pulling caused me to stitch a lot closer to the seam line than I wanted.  In the left circle there's about a 3mm distance from the seam to the top stitching--this seam is by my ribcage.  In the right circle there's only about 1mm from the seam to top stitching...right at the waist. :(  Since it will get more top stitching, and there's also a waist tape for strength, I'm not too worried about it now. 

Failings

I failed at sewing the last few days.  Really, really failed.

First of all, someone left a burner on for 4 hours the other day--low enough that you couldn't see any flame, so when I finally noticed it, the house smelt like gas.  How is that relevant?  Well, I was afraid to do anything lest I end up in flames.  Seriously, I had visions of a  Watchmen-like fiery death running through my head.

Then I just couldn't quilt.  I tried sewing the sashing on the fourth row of my Halloween quilt, and it was worse than the first row I ever sewed.  I picked out 3 of my 4 rows of in-the-ditch stitches because they didn't catch the sashing in the back.  Then 2 out of 3 of those rows still had to have some "touch ups" to catch all the sashing the second time around.  The one that I didn't have to touch up, well, it's just pretty wobbly looking.

But I'm leaving it; I don't want to get frustrated!

At least I could still sew garments, and spurred along by the sew-along, I started sewing another corset:

I got the lining entirely finished; in fact after this picture, I sewed my seam allowances down flat about 1/8 away from the original seam.  The busk is all in, the waist tape is all in, and the front two panels have their top layer and fashion fabric on -- it's some moleskin/suedecloth with a plasticy stuff fused to it, and it looks pretty much like real leather.

I made the pattern myself, but I didn't make a mockup, so we'll see how that comes along!  I was already just a tad bit off with my middle panel; I marked the waist line, but there's more space at the top of it than at the bottom.  There's only two front panels, and three middle/back panels, so I'm afraid the hip curves may start too much towards the front until it get's laced tightly.  But like I said, we'll see.

Progress 2.0

In between sewing the corset, I'm also sewing together the center of my quilt.  It's starting to look like an actual blanket now!

You can tell from the sashing strip at the bottom right that I'm not the greatest at this--but this is my first time doing it!  As I mentioned before, I'm using the quilt as you go method, though instead of using a blanket stitch to hold it all together, I'm "stitching in the ditch" of the front sashing, and carefully pinning to make sure I get the back sashing sewn down with it.  The front sides look pretty good, right?  My stitches are almost invisible up top, except for a few spots where I sometimes "wandered" a teensy bit.  The back, though... I'm not sure if it's stretching out to make uneven strips because I didn't cut on grain, or what. 

But since it's the first time I've done it, as long as it's all sewn down and it hides all the raw edges, I'm happy!

So far I've only done three of the rows that I planned out in this post, so here's to hoping I improve more as well.  I didn't know this part would be so B O R I N G, though!  I didn't mind quilting it, I didn't mind cutting all the sashing... but jeez, sewing all the sashing on is kind of monotonous.  At least when I see it come altogether and look a little more finished, I get happy. :)

Progress

So I haven't done much knitting lately, but I've done a whole lot of sewing.

It came time to post our mockups for the 1911 corset sew-along. Here's mine!

It looks pretty good, in my opinion--I'm particularly happy that I drafted the hips pretty well on my computer program. What I didn't draft well, though, was the increase in the underbust measurement:

It was way too big, and this was bothering me--should I just take out the amount I added?  Would I really fit into an unmodified pattern for a 23 inch waist from the waist up?  If I take that away, should I add some length up top?  After all, I was kind of worried about some of the fat displacement you can see in the pictures, and it didn't seem like it would meet my underbust line very well, either.

But Jo over at Bridges on the Body suggested just taking out the extra first, before deciding on adding length.  I'm glad I did!

There are a few issues with creasing, which I believe to be just the fabric and the lack of boning.  Most importantly: there's no "spill-age"! And I may even need to take out a teensy bit from the length at the top front so it doesn't interfere with my underbust now.  I already did some of this more "cosmetic" shaping at the bottom of the corset; it won't be too hard to adjust the top, so I doubt I'll even try on my mockup again.

Now I'm ready for the next step! :)